Pimoroni Servo 2040 Hardware

../_images/pim-servo-2040.jpg

The Pimoroni Servo 2040 is a CircuitPython microcontroller board supporting 18 hobby servo outputs. Following are some preliminary notes on the device.

Technical Details

  • Powered by RP2040 (Dual Arm Cortex M0+ running at up to 133Mhz with 264kB of SRAM)

  • 2MB of QSPI flash supporting XiP

  • 18 sets of header pins for connecting 3 pin hobby servos

  • Supports higher voltage servos (up to 11V) *

  • 6 addressable RGB LEDs/Neopixels

  • 6 sets of header pins for connecting analog sensors

  • Onboard voltage and current sensing

  • Reset and BOOT button (the BOOT button can also be used as a user button)

  • USB-C connector for programming and power (3A max)

  • Screw terminals for supplying external power (with reverse polarity protection) (10A max continuous current)

  • QT (STEMMA QT/Qwiic) connector for breakouts

  • Measurements: 62mm x 42mm x 12mm (L x W x H, including connectors). The mounting holes are M2.5 and 2.7mm in from each edge.

Pin Configurations

Partial list from the schematic:

  • GPIO0 to GPIO17: servo outputs SERVO1 through SERVO18

  • GPIO18: six onboard NeoPixels

  • GPIO20: I2C_SDA for the Stemma connector

  • GPIO21: I2C_SCL for the Stemma connector

  • GPIO23: user switch input (also the BOOT switch)

  • GPIO22, GPIO24, GPIO25: ADC multiplexer channel

These pins are defined in the board module:

  • board.LED_DATA

  • board.SERVO_1 through board.SERVO_18

  • etc.

Sample Code

Direct downloads:

 1# pim_servo_2040_demo.py
 2
 3# Demo for the Pimoroni Servo 2040 board.
 4
 5# import firmware modules
 6import time
 7import board
 8import digitalio
 9import neopixel_write
10
11# import the locally defined servo module
12import servo
13
14#================================================================
15print("Creating hardware interfaces.")
16
17# create hardware interfaces
18
19# NeoPixel array
20pixels = digitalio.DigitalInOut(board.LED_DATA)
21pixels.direction = digitalio.Direction.OUTPUT
22frame_buffer = bytearray(3*board.NUM_LEDS)
23
24# specify which servo pins to use
25pins = [board.SERVO_1, board.SERVO_2, board.SERVO_3, board.SERVO_4]
26
27# create a servo object for each pin
28servos = [servo.Servo(pin) for pin in pins]
29
30#================================================================
31def set_led(i, color):
32    if i < board.NUM_LEDS:
33        frame_buffer[i*3]   = color[1] # green
34        frame_buffer[i*3+1] = color[0] # red
35        frame_buffer[i*3+2] = color[2] # blue
36        neopixel_write.neopixel_write(pixels, frame_buffer)
37
38#================================================================
39
40while True:
41    print("Starting main loop.")
42
43    # flash the sequence quickly
44    for i in range(board.NUM_LEDS):
45        print("Flashing LED", i)
46        set_led(i, (0, 0, 255)) # blue
47        time.sleep(0.1)
48        set_led(i, (0, 0, 0))
49
50    # move each servo in sequence
51    for i, s in enumerate(servos):
52        print("Moving servo", i)
53        s.write(90)
54        set_led(i, (0, 255, 0)) # green
55        time.sleep(0.5)
56        s.write(0)
57        set_led(i, (0, 0, 0))