Double Transducer: Rotational Speed to Heat

Team members:
Lily Hummel & Caleb Sun

Caleb’s Double Transducer

Detail Pictures

 

Process Pictures

 

Lily’s Double Transducer

Detail Pictures

 

 

 

Process Photos

 

 

Video

Narrative Description

Our double transducer turns rotational speed to physical heat. When something turns the knob at the left side of the board, a little motor makes a piece of yellow paper move closer to a distance reader. The distance reader makes a lightbulb heat up as the yellow paper gets closer. An LCD display shows the distance and “heat” values.

Discussion

The beginning stages of the project actually went smoothly, when we were just wiring up individual parts and configuring them. What a lot of the trouble came from was with configuring parts to each other. The ultrasonic ranger for one was extremely finicky and would refuse to work at certain points, and the Servo arm had to be placed at a certain angle and calibrated specifically.

When everything began to work together, things came down to just manual calibration, which introduced a different issue. Since we shared our code, the code was only calibrated to Caleb’s transducer, and caused issues when copied over to Lily’s. This might just call for more robust code that doesn’t have to be calibrated manually, or possible automatic calibration that we didn’t have the scope to figure out.

Something we learned was the importance of compartmentalization in the process of making a machine. Starting off, the task was extremely overwhelming. But by breaking apart the transducer into four portions that we could work on one-by-one, it was much more manageable. The different segments made it easier to conduct research, diagram, and ultimately create.

Block Diagram

Semantic Diagram

Code

//Code first records RPM of the rotary encoder and maps value to angle of servo motor
//Second, the ultrasonic ranger detects its distance from the servo motor, and the distance is mapped to the intensity of light
//Finally, the light turns on
//Map values are tuned to Caleb's transducer

//Pins:
//Rotary encoder:
//DT -> 2
//CLT -> 3
//Ultrasonic Ranger:
//trig -> 10
//echo -> 13
//Lightbulb:
//Light -> 6
//Servo Motor -> 4

//Ultrasonic ranger code from: https://www.circuitbasics.com/how-to-set-up-an-ultrasonic-range-finder-on-an-arduino/
// Timing Code from: https://courses.ideate.cmu.edu/60-223/s2023/tutorials/code-bites#blink-without-blocking

#define ENC_COUNT_REV 620
#include <Servo.h>
#include <Wire.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#define trigPin 10
#define echoPin 13
#define lightPin 6

extern uint16_t twi_readFrom_timeout;
extern uint16_t twi_writeTo_timeout;
extern bool twi_readFrom_wait;
extern bool twi_writeTo_wait;

Servo doorMotor;
LiquidCrystal_I2C screen(0x27, 16, 2);
 
volatile long encoder_value = 0;
int interval = 1000;
int x = 123;
int motorPos = 0;
long previousMillis = 0;
long currentMillis = 0;
int lightVal = 0;
int rpm = 0;
int o = 0;
int m2 = 0;
int m = 0;
 
int Servo_pin = 4;
int DT_pin = 2;
int CLK_pin = 3;
  
void setup() {
  pinMode(DT_pin , INPUT_PULLUP);
  doorMotor.attach(Servo_pin);
  pinMode(CLK_pin , INPUT);
  
  Serial.begin(9600);
  pinMode(trigPin, OUTPUT);
  pinMode(echoPin, INPUT); 

  pinMode(lightPin,OUTPUT);

  attachInterrupt(digitalPinToInterrupt(DT_pin), interrupt_on_pulse, RISING);

  screen.init();
  screen.backlight();
  screen.clear();
  screen.setCursor(12,1);
  screen.print("o:");
  screen.setCursor(6,0);
  screen.print("m:");
  screen.home();
  screen.print("i:");
}
 
void loop() {
  int motorPos = 0;
  // Record the time
  currentMillis = millis();

  if (currentMillis - previousMillis > interval) {
 
    previousMillis = currentMillis;
 
    // Calculate revolutions per minute
    rpm = (int)(encoder_value * 60 / ENC_COUNT_REV);
    
    int i = map (abs(rpm),0,20,0,99);
    if (i >99) {
      i = 99;
    }
    screen.setCursor(2,0);
    screen.print(abs(i));

    int motorPos = map (abs(rpm), 0, 20, 35, 80);
    // Safeguard against overload from Rotary Encoder, if motorPos is mapped to a value higher than 80 it defaults to 80
    if (motorPos > 80) {
      doorMotor.write(80);
    }
    // Regular write, causes motor to move to mapped angle
    else {
      doorMotor.write(motorPos);
    }
    delay(25);
    
    m = map (motorPos, 35,80,0,99);
    if (m > 99) {
      m = 99;      
    }
    screen.setCursor(8, 0);
    screen.print(m);

    encoder_value = 0;
  }

  int duration, distance; 
  
  digitalWrite(trigPin, LOW); 
  delayMicroseconds(2); 
  digitalWrite(trigPin, HIGH); 
  delayMicroseconds(10); 
  digitalWrite(trigPin, LOW); 

  duration = pulseIn(echoPin, HIGH); 
  distance = (duration / 2) * 0.0344; 


  lightVal = map (distance,4.5,12,255,0); 

  int o = map(lightVal,0,255,0,99);
  if (distance > 15) { 
    lightVal = 500; 
    o = 99;
    } 
  
  screen.setCursor(14,1); 
  screen.print(abs(o));

  analogWrite(lightPin,abs(lightVal)); 
  }

void interrupt_on_pulse() {
  int val = digitalRead(CLK_pin);
  if(val == LOW) {
    encoder_value++;
  }
  else {
    encoder_value--;
  }  
}