Power

The big question in this realm is usually batteries versus plug-in. Here are some considerations to help you weigh your options:

Batteries

Batteries’ capacities are measured in Amp-hours (Ah), or milliAmp-hours (mAh). A 1Ah battery can give you 1A of current continuously for an hour, or 500mA continuously for 2 hours, etc.

Rechargeable batteries tend to have lower capacities than alkaline (non-rechargeable) ones. Batteries will degrade over time and lose capacity, requiring replacement, and will suffer significant power loss at cold temperatures. Some rechargeables must be fully drained before charging, or they’ll suffer a “memory” problem where they lose a lot of capacity; other rechargeables should not be fully drained or they’ll be damaged. These different qualities (and others) are functions of the particular chemistry used in the battery.

Battery types:

150mAh lithium battery, image from Adafruit Lithium-ion: many different sizes/capacities available, rechargeable via USB port using this $15 Adafruit board; that same Adafruit board will give you a 5V output though the battery attached to it is not a 5V. Available capacities are 150mAh (little!) through 6,600mAh and bigger. Improperly charged lithium batteries can swell physically and even explode!

AA, AAA, and D batteries, modified from user "Lead holder"'s [original image at Wikimedia Commons](https://commons.wikimedia.org/wiki/File:Batteries_comparison_4,5_D_C_AA_AAA_AAAA_A23_9V_CR2032_LR44_matchstick-1.jpeg) and released under CC BY-SA 3.0 AA, AAA, D batteries: rechargeable versions of all these exist, and holders that give you different voltage outputs by stacking up different numbers of cells. Rechargeable AA, AAA, and D cells are rated at 1.2V; they differ in their physical size and power capacity. Small AAA cells hold ~1,000mAh, while big D cells hold ~5,000 mAh.

Anker PowerCore power bank, image via Amazon.com A rechargeable USB “power bank” is also another option. This $25 one, for instance, claims to provide 10,000mAh, i.e. 10Ah, at 5V.

Plug-in

Usually the better choice for permanent installations. No need to worry about changing out or recharging the battery!

USB power, image via Amazon.comAny device with a powered USB port (the type which would charge a phone, etc.) is capable of powering an Arduino Uno. (When your computer is not sending data back and forth through the USB cable to the Arduino, it is behaving the same as this little plug.) You can use a simple little charger of this type to give you 5V right into the Arduino.

9V power supply with barrel jack, image via Amazon.comYou can also provide 7–12V directly to the Arduino’s barrel jack power input to run it. A simple power supply like this 9V unit is nice because it has a male barrel jack, and can be plugged in to the Arduino directly.

Panel mount barrel jack, image via JamecoAlternatively, you can add a panel-mount female barrel jack (Phys Comp part 0698) onto the enclosure of your device so that the power plug does not need to make it all the way physically to the Arduino inside the box. In this case, the 7–12V from the power supply should be plugged into the Arduino’s VIN pin, and the ground or negative power supply line to the Arduino’s GND pin. Be sure to use a multimeter to check which pin coming out of the barrel jack is positive and which is negative before you wire it up!

In any case, it’s usually a good idea to have a power switch

The user can switch power on and off to save energy or reset the Arduino as needed.

Rocker switch, image via AmazonAn easy choice for this switch is a simple rocker switch with I/0 markings on it, like this one (Phys Comp part number 0222). This sort of switch is legible to most users as a power switch, and also has clear indications so it’s obvious which way it’s switched. (Cut a rectangular hole in an enclosure wall to insert this panel-mounted switch.)

Voltages can be traded up and down as needed

Be careful to keep different voltages separated! If you attach a wire from 12V to 5V, that is akin to attaching a wire from 5V to ground: it’s a short circuit and will cause lots of current to try to flow from 12V to 5V. Mark your different voltages carefully and keep them separated physically and electrically.

LM7805 voltage regulator, image via Amazon A voltage regulator is a device that can turn one voltage into another: for instance, 9V into 5V (the LM7805 (Phys Comp part 7805) will do that particular transformation). These parts will get warm if you are passing higher currents through them, so they may require heatsinking. This particular part can take an input voltage in the range of 7–25V and give 5V out.

5V step-down regulator, image via Pololu (part D24V5F5) There is a family of voltage regulators, often called DC–DC transformers, which can “step-up” or “step-down” voltages, i.e. turn 3.7V into 5V, or 12V into 9V, etc. Again, with these, a relevant question is “how much current needs to be transformed?” If it’s a lot (more than ~2A) consider using multiple voltage sources that give you the voltages you need directly, instead of using regulators. For some examples of DC–DC converters, see Phys Comp part 0834 (steps up a lower voltage to 5V), part 0850 (steps down a higher voltage to 5V), and 0846 (an adjustable regulator, which can step a lower voltage to any output voltage between 4V and 25V).

Fabrication

There are many, many “tricks of the trade” that tinkerers, engineers, and builders have discovered over thousands of years of building things. A few pieces of advice especially relevant to the sort of work we do in Intro to Physical Computing are presented here, but these really form only the tip of the tip of the iceberg.

Soldering is strongly preferred over breadboarding!

Breadboards are great for throwing things together. They are not well-suited for long-term installations. Wires get pulled out or jiggle loose, contacts corrode, etc.

Protoboard, image via AmazonInstead, after you breadboard everything to confirm the electronics are all correct and working, transfer your design to a board with soldered connections. This is made especially easy if you use one of our protoboards that match a medium breadboard (Phys Comp part 0034)

Solid core wire, image from Petar Milošević via Wikimedia Commons (https://commons.wikimedia.org/wiki/File:Electric_guide_3%C3%972.5_mm.jpg), shared under CC BY-SA 4.0Solid core wires (like Phys Comp parts 2076, 2078, 2080, 2082) will hold a position they are bent into. They will break if bent back and forth repeatedly.

Stranded wire, image from Scott Ehardt via Wikimedia Commons (https://commons.wikimedia.org/wiki/File:Stripped_wire.jpg) Stranded wires (like Phys Comp parts 2086, 2087, and 2089) are made of many small wires twisted together. They will withstand many cycles of bending back and forth without breaking. They don’t hold a form when flexed, and will tend to return to a neutral straightish orientation.

In all cases, care must be taken that wires, and their connections, will not be pulled on, torqued much, crushed, or bent at a tight radius during the regular course of the project being used. “Strain relief” is the art and science of protecting wires and connectors from undue force, and if you want your creations to have reasonable longevity, you’ll be careful about it!

When wires are traveling through an enclosure wall, there are two approaches:

Cable "gland" passthrough, image from McMaster Option one: keep the cable(s) intact all the way through the wall. A panel-mount “cable gland” (weird name; also called a “cord grip”) mounts into a panel and holds a cable firmly but without damaging it. The unbroken wire passes all the way through, from the outside to the inside of the enclosure. When the cable gland is tightened, it will hug the walls of the wire and seal out moisture/air from passing into the enclosure.

8 pair cable connector, image from MPJA Option two: use a panel-mount connector which can be plugged and unplugged. Phys Comp part 0693, for instance, allows up to 8 wires to be made into a connector. The connector has a panel mount side (pictured on the right here), which is affixed to the enclosure. This mates with a cord-end side (pictured on the left), which screws on to your cables.

If the user should be able to open the box, don’t glue it shut

If you’ll ever want to get inside your enclosure, use a hinge or similar so that a door can be opened.

Hinge, image from McMaster For a mechanical hinge: see suppliers on the useful links page for some choices; McMaster is an excellent source because they have a huge catalog and very well-organized search.

By Autopilot - Own work, CC BY-SA 3.0, https://commons.wikimedia.org/w/index.php?curid=17579009 You may also want a surface to be foldable or flexable using a “living hinge.” This refers to the technique of making lots of small cuts in a plane (typically done with a laser) which will allow it to flex.

A note on polish/finish

Consider the level of polish/finish you’re aiming for. You do not necessarily need to make a beautiful object—but if you have the time, thinking carefully about aesthetic concerns, and producing a handsome final piece will often greatly enhance the user’s experience of interaction with it.

Materials speak loudly. Consider a surface of your product finished with three different materials:

  • A piece of varnished wood with exposed grain shows how it grew, and later, how it was cut from the tree; it will communicate warmth and tangibility, as well as referring to the craft of past generations.
  • A piece of polished aluminum in the same place has another valence altogether: it may read like a part of a machine from the nineteenth century, or perhaps a reference to midcentury design trends of the 1950s and 60s.
  • A piece of grey 3D-printed plastic will read totally differently for most users: it will communicate cutting-edge fabrication methods—or perhaps twenty-first century plastic consumerism.

Whatever your material choices are, know that they are choices. Even if you default to the easiest, cheapest, or simplest fabrication method available, your visual choices will be part of your users’ interpretation of your final creation. Be purposeful and cognizant of these decisions!